Start with the level on the speakers all the way down or very low so you can just barely hear something coming out. Set the input faders on the channels and the output master faders on the console at 0 or unity if there is a mark. Sing into the mic at a loud level and bring the input gain knob up and meter it so you get 0 VU on the channel. Same thing with the acoustic guitar channel – play loud and hard and set the input gain knob so it solo’s up at 0 VU or close to it. This optimizes the gain structure on the input channels. Turn up the input level on the speakers until you have the volume you want in the room. Adjust balance between the guitar and vocal with the channel faders on the console. This is a rough way to optimize gain structure.
SOLVED: No output to speakers mackie s power mixer
The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance. If you absolutely must change the polarity try internally modifying a TRS adaptor or use an external phase reverser. You can create a 32 or channel mixer with the Mackie Designs MixerMixer combiner.
there are 2 main channels and 2 monitor channels on the rear of the unit. If you want to use it in stereo mode you connect one cable to the far left.
It’s popularity stems from the continual and perpetual difficulty of hooking up audio equipment without suffering through all sorts of bizarre noises, hums, buzzes, whistles, etc. As technology progresses it is inevitable that electronic equipment and its wiring should be subject to constant improvement. Many things have improved in the audio industry since , but unfortunately wiring isn’t one of them.
However, finally the Audio Engineering Society AES has issued a standards document for interconnection of pro audio equipment. AES standard on interconnections — Grounding and EMC practices — Shields of connectors in audio equipment containing active circuitry. However, this document contains suggestions for external wiring changes that should ideally only be implemented by trained technical personnel.
Full text of “Billboard
How to connect speakers to a computer How to connect speakers to a computer Share: Follow these step-by-step instructions to attach speakers to your computer Step 1: Ensure that the computer is turned off. Plug the speakers into the power socket.
May 28, · Sx speakers. Mackie S mixer amplifier. That’s the important parts. This set up has worked well for years. Bought these components in High school, proba.
Strolling Down The Channel Strip What s The Difference? Line In For Mono Channels Power Supplies and Accessory Power A Clean Fade er We realize that you must have a powerful urge to try out your new mixer.
MACKIE M HOOK
Willing to shell out a little more cash? They also come with an integrated phono pre-amp. Put all these together, and the result is a pair of high-performance monitors capable of producing reference-quality sound. They can be mounted on wall with brackets. A sub-port allows for connecting a sub-woofer for enhanced deep bass. Their built-in amplification provides 10 watts per channel, while the speaker cones are uncovered for pure, unobstructed sound.
May 10, · Mackie s stereo output This mixer I am dealing with the Mackie s is a powered mixer which I m connecting 2 main speakers to it. The outputs on this mixer is labeled main left/main speaker out or right/monitor speaker out.
Jan 25, Hi all, My band has a gig where the club provides a stereo power amp and main speakers hung from the ceiling with subs on the floor. We want to use the mackie’s internal amp to drive the monitors. I have the manual where they show some sample scenarios, but I don’t recall it having what I described above. Just checked pdf’s- close, but they don’t.
Connect the front end via mixer line out to the power amp. Then one monitor cable to each left and right side speaker. This worked and we had normal mixing of mains and monitors.
Mackie S Manuals
If you’re having problems with your Mackie mixer, the best thing to do is to isolate the problem, run through the basic, easy-to-remedy possibilities and implement commonsense solutions. Once you confirm that the problem really is with the mixer–and not your cables, signal source, phantom power or other overlooked component–contact Mackie or take your mixer to a certified repairperson.
Make sure the power’s on. If you’re having trouble with your Mackie mixer, start with the obvious stuff. Check that the mixer’s definitely plugged in.
Incidentally, the Mackie Product Hook-Up Guide (Web Editions) were put together from within the conﬁ nes of the Mackie Digital Mosh Pit — located on the second ﬂ oor near the Area Of Refuge — by the well-meaning, super-preening Mackie Macin-tosh Department.
Publishing This series was originally written in , but it has proven to be incredibly popular with hundred of thousands of readers. So we’ve updated the recommendations for This series also formed the basis for the podcasting classes that Jeff created for OSTraining. Choosing the right podcast equipment can be incredibly frustrating and confusing. In this guide, Jeff gives you his honest feedback from a decade of podcasting experience.
Mackie S 8
What subwoofer is best for your car? Super slim subwoofer 1. All aluminum metal housings –good for Ventilation They have specilized in manufacturing auto parts for several years.
Mackie products have been making music across a wide-range of applications since our founding in Woodinville, WA in
Contact cleaner Extra cables Popping and crackling sounds easily ruin a musical performance or speech. The good news is that crackling sounds usually do not indicate a serious problem. In most cases, the noise is because of minor issues such as dirt, aging parts or faulty cables. The bad news is it may require a little bit of time to identify and correct the problem. The Mackie mixer manual puts it the following way: Dust or grime works its way down into the faders or pots, and this causes a crackling noise when you slide the fader up or down.
Spray the faders and pan pots with compressed air to blow away the dust that causes the crackling noises. Clean the faders and pots regularly with compressed air to ensure that they remain dust free. If the crackling noises continues, a deeper cleaning is necessary to correct the problem.
Mackie VLZ4 Manuals
Woofer Horn tweeter Hooking up a crossover in a PA system requires all components to be separate. In a component system, crossovers are “active” rack mounted components, used to split sound frequencies for efficient and adjustable distribution to separate amplifiers and speakers. The use of dedicated amps and speakers for each frequency is called “bi-amping” or “tri-amping,” for two or three-way systems respectively.
Sep 12, · Ultra-light and completely self-contained, the Mackie PPM Professional Powered Mixer features two robust W power amps for mains or .
More to come in the weeks ahead as we go behind-the-scenes in the studio! The preamps were very quiet and clean. Good for recording vocals, guitars, bass and all other instruments. I would use this interface for any application, really. Especially when I knew I was getting Mackie gear to record an exclusive track with! I was able to use that as my central station tied into two sets of monitors and two headphones. When mixing a song, it is always good to have multiple sources to listen through.